Sika AnchorFix®-1 N
Solvent and styrene free based, two-component polyester anchoring adhesive.
- Fast curing
- Standard guns can be used
- Can be used at low temperatures
- ETA to ETAG 029 for anchoring in masonry
- Non-sag, even overhead
- Styrene-free
- Low odour
- Low wastage
Usage
As a fast curing anchoring adhesive for all grades of:- Rebars / reinforcing steel
- Threaded rods
- Bolts and special fastening systems
- In the following substrates:
- Hollow and solid masonry
- Hard natural stone*
- Solid rock*
Advantages
- Fast curing
- Standard guns can be used
- Can be used at low temperatures
- ETA to ETAG 029 for anchoring in masonry
- Non-sag, even overhead
- Styrene-free
- Low odour
- Low wastage
Packaging
| 165 ml standard cartridge | 12 cartridges per box pallet: 105 boxes |
| 300 ml standard cartridge | 12 cartridges per box pallet: 84 boxes |
| 420 ml coaxial cartridge | 12 cartridges per box pallet: 70 boxes |
Colour
| Component A: | white |
| Component B: | black |
| Component A+B mixed: | light grey |
Product Details
ENVIRONMENTAL INFORMATION
Conformity with LEED v2009 IEQc 4.1: Low-Emitting Materials - Adhesives and Sealants
APPROVALS / STANDARDS
Injection system for use in masonry according to ETAG 029, ETA-17/0327, Declaration of Performance 86553674, certified by notified product certification body 1020, certificate of constancy of performance 1343-CPR-M 632-1, and provided with the CE marking
Shelf Life
9 months from date of production
All Sika AnchorFix®-1 N cartridges have the expiry date printed on the label.
Storage Conditions
Stored properly in original, unopened, sealed and undamaged packaging in dry conditions at temperatures between +5 °C and +25 °C. Protect from direct sunlight.
Density
~1.74 kg/l (component A+B mixed)
Compressive Strength
| ~75 N/mm2 (7 days, +20 °C) | (EN 196) |
Tensile Strength in Flexure
| ~30 N/mm2 (7 days, +20 °C) | (EN 196) |
Modulus of Elasticity in Flexure
| ~4000 N/mm2 | (EN 196) |
Service Temperature
| Long term | -40 °C min. / +50 °C max. |
| Short term (1–2 hours) | +80 °C |
Application
Mixing Ratio
Component A : component B = 10 : 1 by volume
Layer Thickness
3 mm max.
Sag Flow
Non-sag, even overhead
Product Temperature
Sika AnchorFix®-1 N must be at a temperature of between +5 °C and +35 °C for application.
Ambient Air Temperature
-5 °C min. / +40 °C max.
Dew Point
Beware of condensation.
Substrate temperature during application must be at least 3 °C above dew point.
Substrate Temperature
-5 °C min. / +40 °C max.
Curing Time
| Temperature | Open time - Tgel | Curing time - Tcur |
| +35 °C – +39 °C | 2 minutes | 20 minutes |
| +30 °C – +34 °C | 4 minutes | 25 minutes |
| +20 °C – +29 °C | 6 minutes | 45 minutes |
| +15 °C – +19 °C | 15 minutes | 80 minutes |
| +10 °C – +14 °C | 20 minutes | 100 minutes |
| +5 °C – +9 °C | 25 minutes | 2 hours |
| 0 °C – +4 °C 1 | 45 minutes | 3 hours |
| -5 °C – -1 °C 1 | 90 minutes | 6 hours |
1 Minimum cartridge temperature: +5 °C
SUBSTRATE QUALITY
- Mortar and concrete must be at the required strength. No need to be 28 days old.
- Substrate strength (concrete, masonry, natural stone) must be verified.
- Pull-out tests must be carried out if the substrate strength is unknown.
- The anchor hole must always be clean, dry, free from oil and grease etc.
- Loose particles must be removed from the holes.
- Threaded rods and rebars have to be cleaned thoroughly from any oil, grease or any other substances and particles such as dirt etc.
MIXING
Getting the cartridge ready: 165 / 300 ml
|
| 1. Unscrew the cap |
|
| 2. Cut the film |
|
| 3. Screw on the static mixer |
|
| 4. Place the cartridge into the gun and start application |
Getting the cartridge ready: 420 ml
|
| 1.Unscrew & remove the cap |
|
| 2. screw on the static mixer |
|
| 3. Place the cartridge into the gun and start application |
When the work is interrupted the static mixer can remain on the cartridge after the gun pressure has been relieved. If the resin has hardened in the nozzle when work is resumed, a new nozzle must be attached.
CLEANING OF TOOLS
Clean tools and application equipment with Sika® Colma Cleaner immediately after use. Hardened / cured material can only be mechanically removed.