Sikafloor®-300
Sikafloor®-300 is a two part, aliphatic, solvent free, very low VOC emission certified, elastic, self-smoothing polyurethane resin. The product is containing epoxy paste mixed in its substrate for a broad color range.
- Very low VOC emission
- Solvent free
- Comfortable
- Footwarm
- Reduces footfall sound
- Permanently elastic
- Good mechanical resistance
- Very high yellowing resistance
- Decorative designs possible using coloured chippings etc.
- Easy to apply
- Low maintenance finish
Usage
- Elastic smooth wearing course for Sika Comfortfloor® range
- For decorative floor finishes
- Particularly suitable for hospitals, schools, sales premises, showrooms, entrance halls, lobbies, openplan offices, museums and residential use.
- For interior use only
Advantages
- Very low VOC emission
- Solvent free
- Comfortable
- Footwarm
- Reduces footfall sound
- Permanently elastic
- Good mechanical resistance
- Very high yellowing resistance
- Decorative designs possible using coloured chippings etc.
- Easy to apply
- Low maintenance finish
Packaging
Part A | 15.00 kg containers |
Part B | 5.00 kg containers |
Part A+B | 20.00 kg containers |
Colour
Part A Resin | Coloured Liquid |
Part B Hardener | Transparent Liquid |
Available as substrate and in almost unlimited choice of colour shades.
Note: With bright colours such as yellow , orange etc., colour variations may occur
Product Details
APPROVALS / STANDARDS
Synthetic resin screed material according to EN 13813:2002, Declaration of Performance 0208120400200000251041, certified by notified factory production control certification body 0620, and provided with the CE marking.
Chemical Base
Polyurethane
Shelf Life
12 months from date of production
Storage Conditions
The packaging must be stored properly in original, unopened and undamaged sealed packaging, in dry conditions at temperatures between +5 °C and +30 °C.Density
Part A | ~1.45 kg/l |
Part B | ~1.16 kg/l |
Part A+B mixed | ~1.40 kg/l |
All Density values at +23 °C
Solid content by weight
~100 %
Solid content by volume
~100 %
Shore A Hardness
~84 (14 days / +23 °C) | (DIN 53505) |
Tensile Strength
~ 8.0 N/mm² (14 days / +23 °C) | (DIN 53504) |
Tensile Adhesion Strength
> 1.5 N/mm2 (failure in concrete) | (EN 13892-8) |
Chemical Resistance
Sikafloor®-300 always has to be sealed with Sikafloor®-304 W. Therefore, refer to chemical resistance of Sikafloor®-304 W.
Application
Mixing Ratio
Part A : Part B = 75 : 25 (by weight)
Layer Thickness
2.80 kg/m² - film thickness ~2.0 mm.
Refer to the System Data Sheet.
Ambient Air Temperature
+15 °C min. / +30 °C max.
Relative Air Humidity
80 % max.
Dew Point
Beware of condensation!
The substrate and uncured floor must be at least 3 °C above dew point to reduce the risk of condensation or blooming on the floor finish.
Substrate Temperature
+15 °C min. / +30 °C max.
Substrate Moisture Content
< 4 % pbw moisture content.
Test method: Sika®-Tramex meter, CM - measurement or Oven-dry-method.
No rising moisture according to ASTM (Polyethylene-sheet).
Pot Life
Temperature | Time |
+10 °C | ~120 minutes |
+20 °C | ~90 minutes |
+30 °C | ~45 minutes |
Curing Time
Before overcoating Sikafloor®-300 allow:
Substrate temperature | Minimum | Maximum |
+10 °C | 24 hours | 72 hours |
+20 °C | 16 hours | 48 hours |
+30 °C | 16 hours | 36 hours |
Applied Product Ready for Use
Temperature | Foot traffic | Light traffic | Full cure |
+10 °C | ~30 hours | ~48 hours | ~6 days |
+20 °C | ~16 hours | ~24 hours | ~4 days |
+30 °C | ~12 hours | ~18 hours | ~3 days |
Note: Times are approximate and will be affected by changing ambient conditions.
Consumption
~1.4 kg/m 2/mmMIXING
Prior to mixing, stir part A mechanically. When all of part B has been added to part A, mix continuously for 2 minutes until a uniform mix has been achieved. To ensure thorough mixing pour materials into another container and mix again to achieve a consistent mix. Over mixing must be avoided to minimise air entrainment.
Mixing Tools
Sikafloor®-300 must be thoroughly mixed using a low speed electric stirrer (300–400 rpm) or other suitable equipment.
APPLICATION
Prior to application, confirm substrate moisture content, relative humidity and dew point.
Sikafloor®-300 is poured and spread evenly by means of a serrated trowel or pin rake. Once Sikafloor®-300 is “tack-free” apply the seal coat.
CLEANING OF TOOLS
Clean all tools and application equipment with Thinner C immediately after use. Hardened and/or cured material can only be removed mechanically.
Please refer to the Sika Method Statement Mixing & Application