Sikalastic®-530 Thermic AP

Certified Singapore Green Building Product - SGBC
Green Marks 4 Ticks: Leader

Acrylic

12 months from date of production

The Product must be stored in original, unopened and undamaged sealed packaging in dry conditions at temperatures between +5 °C and +30 °C. Always refer to packaging.

Refer to the current Safety Data Sheet for information on safe handling and storage.

(60 ± 3) % 

(50 ± 3) % 

ROOF COATING:

REINFORCED ROOF WATERPROOFING:

Primer* : For metal substrate, use Davco Primer XP or Davco/Sika recommended primer.
 

Note: Consumption data is theoretical and does not allow for any additional material due to surface porosity, surface profile, variations in level, wastage or any other variations. Apply product to a test area to calculate the exact consumption for the specific substrate conditions and proposed application equipment.

0.045 W/m.K

80 % maximum

Beware of condensation. The substrate and uncured applied roof material must be at least +3 °C above dew point to reduce the risk of condensation on the surface finish.

No rising moisture (ASTM D4263, polyethylene sheet)

The substrate must be visibly dry with no standing moisture.

4 – 6 hours

Note: Times are approximate and will be affected by changing ambient conditions, particularly temperature and relative humidity.

Select the most appropriate equipment required for the project:

SUBSTRATE PREPARATION EQUIPMENT

• Abrasive blast cleaning / planing / scarifying or grinding equipment.

• Manual or mechanical wire brushes.

• High pressure power washer.

For other types of preparation equipment, contact Sika Technical Services.

MIXING EQUIPMENT

• Electric single or double paddle mixer (300–400 rpm) with spiral paddle

APPLICATION EQUIPMENT

• Brush: Soft bristle

• Roller: Solvent resistant fleece

IMPORTANT

System design

Consider the following when designing the system:

1. The supporting structure must be of sufficient structural strength to support all new and existing layers of the system build-up.
2. If used as a roof system, the complete system must be designed to withstand and be secured against wind uplift loadings.
3. Reinforcement (partial or total) must be used over dynamic cracks and joints.

GENERAL

Substrates must be free of standing water (no puddles) clean and free of all contaminants such as dirt, oil, grease, coatings, laitance, surface treatments and loose friable material.

All dust, loose and friable material must be completely removed from all surfaces before application of the product, and associated system products, by industrial vacuuming equipment.

To confirm adequate surface preparation and product adhesion, carry out a trial before full application together with adhesion tests.

CEMENTITIOUS SUBSTRATES

1. Substrate must be sound with a minimum tensile adhesion strength of 1.5 N/mm², clean, dry and free of all contaminants such as dirt, oil, grease, coatings, laitance, surface treatments and loose friable material.
2. New concrete must be cured for at least 28 days and have a tensile strength > 1.5 N/mm².
3. Cementitious substrates must be prepared mechanically using substrate preparation equipment to remove cement laitance and achieve an open textured gripping surface profile suitable for the product thickness.
4. High spots can be removed by grinding.
5. Weak cementitious substrates must be removed and surface defects such as blow holes and voids must be fully exposed.
6. Repairs to the substrate, filling of joints, blowholes / voids and surface levelling must be carried out using appropriate products from the Sikafloor®, Sikadur® and Sikagard® range of materials. Products must be cured before application of the waterproofing system.

BRICK AND STONE

1. Mortar joints must be sound and flush pointed.
2. Replace loose bricks, stone and mortar.
3. Thoroughly clean the surface by power washing and allow to dry.

UNGLAZED CERAMIC TILES

1. Ensure all tiles are securely fixed.
2. Replace any broken, loose or missing sections.
3. Thoroughly clean the surface by power washing and allow to dry.

CLAY TILES

1. Ensure all tiles are securely fixed.
2. Replace any broken, loose or missing sections.
3. Thoroughly clean the surface by power washing and allow to dry.

IMPORTANT

Avoid over-mixing to minimise air entrainment.

Product is supplied ready to use. Before application, mix for at least 1 minute or until the liquid is uniform.

IMPORTANT

Protect from rain

After application, the product must be protected from heavy rain or rain showers until dry to prevent surface damage.

Application of successive coats

To prevent a reduction in product performance the following actions are necessary when applying successive coats.

1. Ensure product is totally dry and the surface is without pinholes before applying successive coats.
2. Remove surface water between coating applications.
3. Confirm overcoating times have been achieved between coating applications.

No application on rising moisture

Do not apply on substrates with rising moisture.
 

INSTALLATION PROCEDURE

Reference must be made to further documentation where applicable, such as a relevant method statement, application manual and installation or working instructions.

PRIMER

Equipment: 

• Fleece roller

• Brush

1. Pour the mixed Product onto the surface. The consumption is specified in the individual primer product data sheet Application Information.
2. Apply the Product evenly over the surface with a brush or fleece roller.
3. Back roll the surface in two directions at right angles with a fleece roller. 

The coating is continuous and pore free.

ROOF COATING

Equipment: 

• Fleece roller

• Brush

First coat

• Install the detailing first (such as corners, upstands, joints) before installation of the main horizontal surfaces.
• Pour the mixed Product onto the substrate. The consumption is specified in Application Information.
• Apply the Product with either a rush or a fleece roller.

• IMPORTANT Avoid going back to re-work areas that are partially dried as this may damage the surface finish. Back roll the surface in two directions at right angles with a fleece roller.

The coating is continuous and pore free.

Second coat

• Install the detailing first (such as corners, upstands, joints) before installation of the main horizontal surfaces.
• Pour the mixed Product onto the substrate. The consumption is specified in Application Information.
• Apply the Product perpendicularly with either a brush or a fleece roller .
• IMPORTANT Avoid going back to re-work areas that are partially dried as this may damage the surface finish. Back roll the surface in two directions at right angles with a fleece roller.

The coating is continuous and pore free.

ROOF WATERPROOFING

Reinforced waterproof membrane

Equipment: 

• Fleece roller

• Brush

First coat

• Install the detailing first (such as corners, upstands, joints) before installation of the main horizontal surfaces.
• Pour the mixed Product onto the substrate. The consumption is specified in Application Information.
• Apply the Product with either a brush or a fleece roller.
• IMPORTANT Avoid going back to re-work areas that are partially dried as this may damage the surface finish. Back roll the surface in two directions at right angles with a fleece roller.

The coating is continuous and pore free.

Reinforcement application

• For the best results work 1.0 m at a time lengthways applying the 1st coat and embedding the reinforcement.
• Make sure reinforcement overlaps are minimum 50 mm.
• Lay the reinforcement onto the wet 1st coat
• Use a short pile roller to roll over the reinforcement and resin

The coating is continuous and pore free.

Second coat

• Check if the reinforcement is embeded properly, if necessary use sand paper to unsure that the surface is even. If the surface was contaminated with dust or dirt clean the surface with water and light detergent, wait until the surface is dry before applying 2nd coat. Remove any standing water before application. 
• Install the detailing first (such as corners, upstands, joints) before installation of the main horizontal surfaces.

• Pour the mixed Product onto the substrate. The consumption is specified in Application Information.
• Apply the Product perpendicularly with one either a brush or a fleece roller.
• IMPORTANT Avoid going back to re-work areas that are partially dried as this may damage the surface finish. Back roll the surface in two directions at right angles with a fleece roller.

The coating is continuous and pore free.

Third coat

• Install the detailing first (such as corners, upstands, joints) before installation of the main horizontal surfaces.

• Pour the mixed Product onto the substrate. The consumption is specified in Application Information.
• Apply the Product perpendicularly with one either a brush or a fleece roller.
• IMPORTANT Avoid going back to re-work areas that are partially dried as this may damage the surface finish. Back roll the surface in two directions at right angles with a fleece roller.

The coating is continuous and pore free.

Clean all tools and application equipment with water and mild detergent immediately after use. Hardened material can only be removed mechanically.